How to Clean Grout on Tile Floors: 4 Methods That Work

How to clean grout on tile floors, from the gentlest method to the strongest: brush, baking soda and peroxide, oxygen bleach and steam. Plus what never to use.

By the Small Space Reset editorial team · Updated · 4 min read

Grout is porous, sits lower than the tile and collects everything a mop pushes into it. That is why a floor can look dull even right after mopping. The methods below go from gentlest to strongest. Start at the top and move down only if the grout is still stained.

Before you start

  • Vacuum or sweep first. Loose grit turns into mud once it is wet.
  • Identify your tile. Ceramic and porcelain handle all four methods. Natural stone such as marble, travertine, limestone and slate needs a pH-neutral stone cleaner only.
  • Test a hidden spot. Try the method on one grout line in a corner, especially with colored grout.
  • Ventilate and wear gloves. Open a window, and protect your knees with a folded towel or pad.
  • Use a nylon brush. A stiff nylon grout brush or an old toothbrush is enough. Metal bristles scratch tile and break up grout.

Method 1: Warm water and a stiff brush

Best for light, recent dirt and for regular upkeep.

  1. Spray or pour warm water along the grout lines.
  2. Wait two minutes.
  3. Scrub along the line with short strokes.
  4. Wipe up the dirty water with a microfiber cloth, then rinse.

Add a few drops of dish soap for kitchen floors where the dirt is greasy. Rinse well, because soap residue attracts new dirt.

Method 2: Baking soda and hydrogen peroxide

Best for stained grout in small to medium areas.

  1. Mix about two parts baking soda with one part 3% hydrogen peroxide into a thick paste.
  2. Spread it along the grout lines with a spoon or your gloved finger.
  3. Leave it for 10 minutes.
  4. Scrub with the nylon brush.
  5. Rinse with clean water and dry with a cloth.

Baking soda provides gentle abrasion and hydrogen peroxide lightens stains. Mix only what you need and do not store the paste in a closed container.

Method 3: Oxygen bleach

Best for a whole floor or grout that has darkened evenly over time.

  1. Dissolve powdered oxygen bleach (sodium percarbonate) in warm water, following the quantities on the product label.
  2. Pour or mop the solution onto the grout so the lines are flooded.
  3. Let it sit for 10 to 15 minutes. Do not let it dry; add more solution if needed.
  4. Scrub, then mop up the liquid.
  5. Rinse twice with clean water.

Oxygen bleach is gentler on colored grout than chlorine bleach and has no harsh smell. It still needs gloves and a spot test.

Method 4: Steam

Best for deep cleaning without chemicals, on sealed grout in good condition.

  1. Fit the small nylon brush attachment to a steam cleaner.
  2. Move slowly along each grout line.
  3. Wipe away the loosened dirt with a cloth as you go.

Avoid steam on cracked or crumbling grout, since heat and pressure can loosen it further. Check your flooring manufacturer’s guidance before steaming natural stone.

Which method to choose

Situation Start with Effort
Weekly upkeep Method 1: water and brush Low
Stains near the stove or entry Method 2: baking soda and peroxide Medium
The whole floor looks gray Method 3: oxygen bleach Medium
Deep clean once or twice a year Method 4: steam Medium, needs a machine
Natural stone tile pH-neutral stone cleaner Low

What not to use on grout

  • Vinegar or lemon juice on unsealed grout or natural stone. Acids can weaken cement grout over time and etch marble, travertine and limestone.
  • Chlorine bleach as a routine cleaner. It can fade colored grout and wear down sealer.
  • Any mix of products. Never combine bleach with ammonia, vinegar or other cleaners. Rinse thoroughly before switching products.
  • Metal brushes and scouring powders with harsh abrasives. They scratch tile glaze and erode grout.
  • Colored cleaners on white grout. Dyes can leave a tint.

Keep it clean longer: seal the grout

Cleaning is half the job. Cement-based grout stays clean much longer once it is sealed.

  1. Let the grout dry fully, usually 24 hours or more after cleaning.
  2. Apply a penetrating grout sealer along the lines, following the product directions.
  3. Wipe any sealer off the tile surface before it dries.
  4. Keep the floor dry for the curing time given on the label.

To check whether existing sealer still works, drip water on a clean, dry grout line. If it beads, the seal is good. If it soaks in and darkens the grout, reseal. Epoxy grout is not porous and does not need sealing.

A routine that prevents scrubbing

  • Sweep or vacuum tile floors twice a week so grit does not get mopped into the lines.
  • Mop with clean water and change it as soon as it looks cloudy.
  • Use less soap. Too much leaves a film that holds dirt.
  • Run the brush over the worst lines once a month, as part of your Sunday reset.

A grout brush, baking soda and oxygen bleach are all on our cleaning supplies list, so you may already have what you need.

When to call a professional

Cleaning will not fix grout that is cracked, crumbling or missing, or stains that return within days because water is getting under the tile. Those need regrouting or a repair. If you rent, report it to your landlord before attempting a fix yourself.

Frequently asked questions

What is the best homemade grout cleaner?

A paste of baking soda and 3% hydrogen peroxide is the most common homemade grout cleaner. Mix about two parts baking soda with one part peroxide, apply it to the grout lines, wait 10 minutes, scrub with a nylon brush and rinse with clean water.

Can I use vinegar to clean grout?

Avoid vinegar on unsealed or cement-based grout and on natural stone tile such as marble, travertine and limestone. Vinegar is acidic, so repeated use can weaken cement grout and etch stone. On sealed grout with ceramic or porcelain tile, occasional diluted vinegar is lower risk, but gentler methods work as well.

Does bleach damage grout?

Occasional diluted chlorine bleach will lighten stains on white grout, but frequent use can fade colored grout and wear down the sealer. Oxygen bleach is a gentler alternative for regular use. Never mix chlorine bleach with ammonia, vinegar or other cleaners.

How often should grout be sealed?

Cement-based grout is usually resealed every one to two years on floors, and more often in showers. To check, put a few drops of water on a clean, dry grout line. If the water soaks in and darkens the grout within a few minutes, it is time to reseal.

Why does my grout get dirty again so quickly?

Unsealed cement grout is porous and absorbs dirty mop water. Mopping with too much soap also leaves a sticky film that holds dirt. Rinse with clean water after mopping, change the water often and seal the grout once it is clean and fully dry.

Keep going